Water treatment for Vernon and the North Okanagan

Home » Services » Water Softeners » Purus-H2O Sanitizer Series SE1 & SE2 Self-Cleaning Water Conditioners

Viqua

Supplied and installed

Purus-H2O Sanitizer Series SE1 & SE2 Self-Cleaning Water Conditioners

A single-tank well water conditioner that removes hardness, iron and manganese and sanitizes its own media bed with chlorine made from the brine at every regeneration.

Get a quote for your home

Every system is sized to your water and quoted after a free water test, including installation.

Not sure this is the right system? Book a free water test.

Downloads: Spec sheet (PDF) · Owner's manual (PDF)

Already own one?

Replacement parts for this system ship free on orders of $100 or more.

About this system

The Sanitizer Series conditioners treat several well water problems in one tank. The SE1 removes hardness, iron and manganese and raises pH. The SE2 removes hardness, iron and manganese and reduces ammonia. Both use Crystal-Right media, a manufactured silica crystal media that regenerates with ordinary salt and is not damaged by chlorine.

What sets the series apart is the built-in chlorine generator. During each regeneration it uses the existing brine to make a controlled amount of chlorine that sanitizes the media bed. This controls the odours and fouling caused by iron and sulphur bacteria in the tank, with no chemicals or special salt to add.

Three sizes are offered for each model, from 1.5 to 3.0 cu ft of media, handling up to 10 or 15 ppm of iron. The SE1 suits water up to 30, 40 or 50 grains per gallon of hardness and the SE2 up to 60 or 80. Peak flow runs 14 to 19 gpm with full 1 in porting through the valve. An -HS version adds KDF 85 media for hydrogen sulphide up to 0.5 ppm.

The metered electronic valve is programmed for your water test and alerts you when salt is low. Okanagan Aquatech tests your water, sizes the system and installs and services it.

Features

  • Built-in chlorine generator sanitizes the media at every regeneration
  • SE1: hardness, iron and manganese removal plus pH raise
  • SE2: hardness, iron and manganese removal plus ammonia reduction
  • Crystal-Right media regenerates with salt and tolerates chlorine
  • Full 1 in porting through the valve
  • Metered electronic valve with low-salt alert
  • Optional -HS version with KDF 85 for hydrogen sulphide up to 0.5 ppm

Specifications

Models SE1: AWP1054SE1, AWP1354SE1, AWP1465SE1; SE2: AWP1054SE2, AWP1354SE2, AWP1465SE2 (-HS suffix adds KDF 85 for H2S)
Media Crystal-Right (CR100/CR200); 1.5 / 2.5 / 3.0 cu ft (1054 / 1354 / 1465)
SE1 capacity (max / medium / min) 1054: 22,600 @ 16 lb / 20,700 @ 12 / 16,400 @ 6; 1354: 36,900 @ 21 / 33,600 @ 16 / 28,300 @ 9; 1465: 52,000 @ 30 / 47,000 @ 22 / 40,000 @ 13 (grains @ lb salt)
SE2 capacity (max / medium / min) 1054: 34,800 @ 16 / 32,000 @ 12 / 22,900 @ 6; 1354: 60,300 @ 26 / 48,300 @ 16 / 28,200 @ 9; 1465: 84,000 @ 37 / 68,000 @ 22 / 40,000 @ 13
Efficiency at lowest setting SE1: 2,700 / 3,100 / 3,100 gr/lb; SE2: 3,800 / 3,000 / 3,100 gr/lb
Maximum hardness SE1: 30 / 40 / 50 gpg; SE2: 60 / 80 / 80 gpg
Maximum iron 10 / 15 / 15 ppm
Minimum pH SE1: 6.0; SE2: 7.0
Peak flow at 15 psid SE1: 14 / 19 / 19 gpm; SE2: 14 / 17 / 19 gpm
Continuous flow at 5 psid SE1: 6 / 9 / 9 gpm; SE2: 8 / 9 / 9 gpm
Backwash flow SE1: 4.2/5.3, 7.5/9.0, 9.0/10.0 gpm; SE2: 4.2/5.3, 5.3/6.5, 7.5/9.0 gpm
Hydrogen sulphide (-HS models) Up to 0.5 ppm with KDF 85 media
Water pressure 25–100 psi
Water temperature 1–38 °C (33–100 °F)
Electrical 110 V / 50–60 Hz; low-voltage operation
Connections 3/4 in brass (1054, 1354); 1 in brass (1465)
Media tank 10 x 54 in / 13 x 54 in / 14 x 65 in
Brine tank 18 x 36 in (1054); 18 x 40 in (1354, 1465)
Shipping weight SE1: 140 / 220 / 256 lb; SE2: 140 / 220 / 284 lb
Influent requirements At least 3 gpg hardness and 80 ppm TDS; a calcite or Corosex unit may be needed (brochure footnote)
Warranty Unit 5 years; fibreglass mineral tank 10 years; brine tank 5 years; media 1 year; conditional, original owner (Purus manual, page 26)

Maintenance

Keep the brine tank at least one-third full; solar salt is recommended. Do not use block salt, iron-cleaning salt or resin cleaners. If pellet or rock salt is used, clean the brine tank every six months. The control board keeps time on a 3 V lithium CR2032 coin cell, which is replaced when depleted. (Purus Sanitizer Series manual, page 11.)

Replacement parts

  • 3 V lithium coin cell, type 2032 (control board back-up)

Downloads